Waterborne Single-Component Primer
20 Years of Waterborne Coating Excellence
Waterborne Single-Component Primer
Our Single Component Waterborne Floor Primer is a ready-to-use waterborne concrete floor primer that requires no additional hardener. After stirring, its modified resin formulation penetrates the capillary pores of concrete and cement-mortar substrates, helping seal surface dust, reinforce weak surface layers and reduce pinholes.
This penetrating concrete floor primer improves adhesion between the substrate and subsequent floor coatings, helping reduce the risk of bubbling, peeling and delamination. It can be easily applied by roller or brush and offers fast drying for convenient flooring construction.
As an essential primer in our Waterborne Single-Component Flooring System, this Waterborne Single-Component Epoxy Primer is mainly used with compatible waterborne single-component epoxy floor topcoats. It is ideal for light-duty flooring projects in general factories, warehouses, offices and retail stores, providing effective concrete sealing and substrate reinforcement.
Share:
Key Selling Points
Ready‑to‑use single‑component: No hardener mixing required. Apply directly after thorough stirring. Eliminate mixing errors with low application threshold.
High penetration & sealing: Low viscosity penetrates concrete capillaries, traps substrate dust, reinforces friable surface layer and reduces bubbling of topcoat.
Improved inter‑coat adhesion: Acts as an interlayer to facilitate topcoat bonding on cement surfaces and minimize peeling and falling‑off.
Fast drying: Short surface‑dry and hard‑dry time to shorten overall construction schedule.
Easy application: Applicable by roller or brush. For highly porous substrates, two thin coats are recommended.
Technical Parameter
| Item | Specification | Remarks |
| Product Type | Single‑component penetrating sealer primer | Single‑component, no hardener needed |
| Application Method | Stir thoroughly after opening before application | Small amount of dedicated thinner is allowed. Adding water is prohibited. |
| Surface Dry Time (25℃) | ≤3 h | |
| Hard Dry Time (25℃) | ≤12 h | Topcoat application is available after hard dry |
| Water Resistance | Fair | Short‑term water resistance; not for long‑term immersion |
| Ambient Construction Temperature | 5~35℃ | Drying slows down under low temperature |
| Relative Humidity for Construction | ≤80% | No condensation or free water on substrate |
| Substrate Moisture Content | ≤10% | New concrete shall be cured for ≥28 days |
| Storage Condition | Store hermetically in cool and dry place, keep away from fire source | |
| Shelf Life | 12 months | For unopened original package |
A Single Component Waterborne Floor Primer penetrates the capillary pores of concrete and cement-mortar substrates through its low-viscosity modified resin formulation. As an essential product in our Waterborne Single-Component Flooring System, it prepares the floor surface for subsequent coating applications through three main functions:
Deep Penetration: Enters concrete pores to improve surface consolidation and reinforce weak, friable surface layers.
Surface Sealing: Binds residual surface dust, seals porous areas and helps reduce pinholes and bubbling in subsequent coatings.
Improved Topcoat Adhesion: Creates a suitable bonding layer between the concrete substrate and waterborne floor topcoat, reducing the risk of peeling and delamination.
As a penetrating concrete floor primer, it is particularly suitable for preparing sound but porous cement-based substrates before applying waterborne single-component epoxy floor coatings.
Proper concrete surface preparation is essential for achieving good adhesion and sealing performance with a waterborne concrete floor primer.
Before application:
Remove Surface Contaminants: Clean dust, oil, grease, loose particles and other substances that may affect primer penetration.
Repair Surface Defects: Fill cracks, holes and damaged areas with suitable repair materials before priming.
Check Substrate Moisture: Concrete moisture content should not exceed 10%. New concrete should be cured for at least 28 days.
Ensure Suitable Conditions: The substrate must be free of standing water and condensation. Follow the specified construction temperature and humidity requirements.
A clean, sound and properly prepared concrete surface allows the single component waterborne primer to penetrate more evenly and form a reliable base for subsequent floor coatings.
This one component waterborne floor primer is ready to use after thorough stirring, without adding a separate hardener.
Step 1: Stir Before Application
Open the container and stir the primer thoroughly until uniform. Do not add water. If necessary, only use the specified dedicated thinner.
Step 2: Apply with a Roller or Brush
Apply the waterborne floor primer evenly across the prepared concrete surface. Avoid excessive accumulation or uneven application.
Step 3: Apply an Additional Coat When Needed
For highly porous or absorbent concrete substrates, two thin coats are recommended to achieve more uniform sealing and penetration.
Step 4: Apply the Floor Topcoat
Allow the primer to reach the specified hard-dry condition before applying the compatible waterborne single-component epoxy floor topcoat. Ensure the primer surface is clean and suitable for recoating.
1. Does a Single Component Waterborne Floor Primer Require a Hardener?
No. It is a ready-to-use single-component primer. Simply stir thoroughly before application without adding a separate hardener.
2. Can Waterborne Floor Primer Be Applied Directly to Concrete?
Yes. It can be applied directly to properly prepared, sound concrete and cement-mortar substrates. Remove dust, oil and loose materials before application to ensure good penetration and adhesion.
3. How Many Coats of Concrete Floor Primer Are Required?
One coat is generally suitable for ordinary concrete surfaces. For highly porous or absorbent substrates, two thin coats are recommended to improve surface sealing and coverage.
4. Can a Waterborne Floor Primer Be Used as a Final Floor Coating?
No. A waterborne floor primer is designed to penetrate, seal and prepare the substrate. It should be covered with a compatible floor topcoat to provide the required decorative finish and surface protection.
Application Scenario
01
Light‑duty Floors
Applicable Sites: Substrate sealing for light‑duty floors including general warehouses, factories, retail stores, offices and corridors.
Applicable Substrates: Sound concrete and cement‑mortar floors. To be used together with waterborne single‑component floor topcoat.
RELEVANT CASES
READY TO START A PROJECT?
We offer customized high-end water-based paint products and coating solutions. Our professional team is involved throughout the process, precisely meeting your product requirements.
RELATED PRODUCTS
Trusted by Clients in 30+ Countries